Cadet CEC163TW Installation Guide download pdf (Page 4)

INSTALLATION INSTRUCTIONS

STRAIN RELIEF

CONNECTOR

KNOCK-OUT

(TWIST TO REMOVE)

SUPPLY WIRE

GROUNDING

SCREW

1. WARNING

Verify that the electrical supply wires are the same

voltage as the heater.

2. If replacing an existing heater, check the label

of the old heater.

3. All electrical work and materials must comply

with the National Electric Code (NEC), the Occu-

pational Safety and Health Act (OSHA), and all

state and local codes.

4. If you need to install a new circuit or need addi-

tional wiring information, consult a qualied elec-

trician.

5. Use copper conductors only.

6. WARNING

Risk of Electrical Shock. DO NOT install the heat-

er directly above bathtub or sink. DO NOT install

in shower stall area (Manufacturer recommends a

minimum 2 foot clearance).

7. Heater must be installed in a wall can:

Model CE Wall Can CC

8. WARNING

Risk of Fire. DO NOT install the heater in a oor,

in the ceiling, below a towel bar, behind a door,

or anywhere the air discharge may be blocked in

any manner.

9. WARNING

Fire or Explosion May Occur. A heater has hot

and arcing or sparking parts inside. Do not use it

in areas where gasoline, paint, or ammable va-

pors or liquids are used or stored.

10. WARNING

Risk of Electrical Shock. Connect grounding lead

to grounding screw provided. Keep all foreign ob-

jects out of heater.

11. WARNING

Risk of Fire. This heater is hot when in use.

Caution—High Temperature. Risk of Fire. Keep

electrical cords, drapery, furnishings, and other

combustibles at least 3 feet from the front of the

heater and 6 inches above and on both sides.

__________________________

Part One

__________________________

REPLACEMENT: If you are replacing an existing Com-Pak Model, proceed to PART TWO, page 5. Conrm that your existing wall can

is mounted ush with outside of sheetrock. Adjust if necessary.

PLACEMENT: Install vertically. Heater is not approved for horizontal or ceiling mount applications.

CONTROLS: A built-in digital thermostat is included. May not be used with a wall thermostat.

REQUIRED MINIMUM distance of 6 inches from adjacent surfac-

es and 4-1/2 inches from the oor (See Figure 4). However, Cadet

RECOMMENDS 12 inches from adjacent surfaces and oor for

longer and cleaner performance. Heaters must be spaced at least

3 feet apart.

Secure the wall can to the stud with 2 screws (See Figures 1 & 2).

As an option, the rubber shim provided may be attached to side of

wall can to square the wall can to the stud.

How do I install for new construction?

STEP 1

Mount The Wall Can

Figure 1

Figure 2

Face of wall can must extend 1/2

inch or 5/8 inch from face of stud to

allow for thickness of sheetrock.

Attach wall can to stud with screws

through holes provided in wall

can. IMPORTANT: wall can should

be mounted ush with outside of

sheetrock.

STEP 2

Route Supply Wires

Route supply wire from the circuit breaker, to the heater. Remove

a knockout from the wall can and attach the supply wire with a

strain relief connector (not included) leaving a minimum of 6 inch-

es wire lead for later use. Connect supply ground wire to ground-

ing screw in wall can (See Figure 3).

Proceed to PART TWO.

How do I install in an existing wall?

STEP 1

Cut A Hole In The Wall

REQUIRED MINIMUM distance of 6 inches from adjacent surfac-

es and 4-1/2 inches from the oor (See Figure 4). However, Cadet

RECOMMENDS 12 inches from adjacent surfaces and oor for

longer and cleaner performance. Heaters must be spaced at least

3 feet apart.

Cut a hole 8 inches wide by 10-1/4 inches high next to a wall stud.

STEP 2

STEP 3

Route Supply Wires

Mount The Wall Can

Insert wall can into opening; keeping wall can ush with wall

surface. Secure can to wall stud with 2 screws through holes pro-

vided in can. IMPORTANT: wall can should be mounted ush with

ouside of sheetrock.

Proceed to PART TWO.

Route supply wire from the circuit

breaker, to the heater. Remove a

knockout from the wall can and attach

the supply wire with a strain relief con-

nector (not included) leaving a minimum

of 6 inches wire lead for later use. Con-

nect supply ground wire to grounding

screw in wall can (See Figure 3).

Figure 3

Figure 4

Page 4

1 2 3 4 5 6 7 8 9 ... 15 16

Comments to this Manuals

No comments

Cadet CEC163TW Installation Guide Page 4

Comments to this Manuals

Related products and manuals for Space heaters Cadet CEC163TW