Cadet EBKNW Installation Guide download pdf (Page 2)

Operating your thermostat

INSTALLATION INSTRUCTIONS

Warranty

1. All electrical work and materials must comply

with the National Electric Code (NEC), the Occu-

pational Safety and Health Act (OSHA), and all

state and local codes.

2. Use copper conductors only.

3. Turn off power to heater circuit at main discon-

nect panel.

4. Connect grounding lead to grounding screw

provided.

Carefully remove front cover from heater by lifting cover up from the bottom, and then outwards. Set aside. Remove wiring

compartment cover, held by one screw. (Figure 1). This thermostat kit occupies 2.4 cubic inches (39 cubic centimeters).

1. Once installation is complete and power has been restored, turn the thermostat fully on by turning the knob clockwise to

the highest position.

2. When the room reaches your comfort level, slowly turn the thermostat knob counterclockwise until the heater turns off

and a click sound is heard. The heater will automatically cycle around this preset temperature.

3. To reduce the room temperature, turn the knob counterclockwise. To increase the room temperature, turn the knob

clockwise.

After following steps above for a new or previously installed model, then:

Attach heater to the wall, making sure the power supply wires are not pinched between the wall and the heater.

240 Volt: If your SoftHEAT baseboard is 240 volts or 208 volts, connect the two red wires from the thermostat to the two

power supply wires (see Figure 2). Then connect the two black wires from the thermostat to the two black wires from the

heater.

120 Volt: If your SoftHEAT baseboard is 120 volts, connect the two black wires from the thermostat together. Then con-

nect the white wire from the baseboard to the neutral power supply wire (Figure 3). Then connect the black wire from the

baseboard to one of the red wires of the thermostat. Finally connect the remaining red thermostat wire to the remaining

power supply wire.

Inspect all wire connections to be sure they are fastened securely. Push wiring back into the wiring compartment and

attach the wiring compartment cover.

Attach the heater front cover. Restore power at the electrical panel board (circuit breaker or fuse box).

If installing on a new EBHN

heater:

1. Remove the end cap by remov-

ing the screw and clip located on

the back of the heater and sliding

the end cap away from the heater.

Keep screw and clip for future use.

2. Attach the new EBKN ther-

mostat kit by sliding it onto the

heater, making sure no wires are

caught between the thermostat

and heater. Secure in place using

the screw and clip previously

removed.

3. Make wire connections below,

then refer to the EBHN owner’s

guide for instructions on how to

nish installing your heater.

If installing on an older model EBHA heater or a previously installed heater:

A new wiring compartment cover is required for the thermostat to t properly on

an EBHA model heater. Use the wiring compartment cover provided and discard

your old cover.

1. Disconnect the power supply wires and remove the strain relief connector from

the heater. Unscrew grounding lead from ground screw.

2. Remove the heater from the wall. It is easier to replace the thermostat while

the heater is not mounted.

3. Remove the existing end cap or thermostat kit by removing the screw and clip

located on the back of the heater and sliding the end cap away from the heater.

Keep screw and clip for future use.

4. Attach the new EBKN thermostat kit by sliding it onto the heater, making sure

no wires are caught between the thermostat and heater. Secure in place using

the screw and clip previously removed.

5. Route power supply wires through the wiring knockout hole and secure to

heater using the strain relief connector. Reconnect grounding lead to green

ground screw.

For more effective and safer operation and to prolong the life of the

heater, read the Owner’s Guide and follow the maintenance instructions.

Failure to properly maintain the heater will void any warranty and may

cause the heater to function improperly. Warranties are non transferable

and apply to original consumer only. Warranty terms are set out below.

LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any

SoftHEAT (EBKN) thermostat found to be defective within one year after

the date of purchase.

These warranties do not apply:

1. Damage occurs to the product through improper installation or incor-

rect supply voltage;

2. Damage occurs to the product through improper maintenance, misuse,

abuse, accident, or alteration;

3. The product is serviced by anyone other than Cadet;

4. If the date of manufacture of the product cannot be determined;

5. If the product is damaged during shipping through no fault of Cadet.

6. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT

AS SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES

SUCH AS PROPERTY DAMAGE OR FOR CONSEQUENTIAL DAMAG-

ES AND/OR INCIDENTAL EXPENSES RESULTING FROM BREACH

OF THESE WRITTEN WARRANTIES OR ANY EXPRESS OR IMPLIED

WARRANTY.

7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR

CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO

THE SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION

OF REPLACEMENT PARTS DOES NOT MODIFY OR EXTEND THE

UNDERLYING WARRANTIES. REPLACEMENT OR REPAIR OF ANY

CADET PRODUCT OR PART DOES NOT CREATE ANY NEW WAR-

RANTIES.

8. These warranties give you specic legal rights, and you may also

have other rights which vary from state to state. Cadet neither assumes,

nor authorizes anyone to assume for it, any other obligation or liability in

connection with its products other than as set out herein.

If you believe your Cadet product is defective, please contact Cadet

Manufacturing Co. at 360-693-2505, during the warranty period, for

instructions on how to have the repair or replacement processed. War-

ranty claims made after the warranty period has expired will be denied.

Products returned without authorization will be refused.

Parts and Service

Visit cadetheat.com/parts-service for information on where to obtain parts

and service.

Reduce-Reuse-Recycle

This product is made primarily of recyclable materials. You

can reduce your carbon footprint by recycling this product at

the end of its useful life. Contact your local recycling support

center for further recycling instructions.

Page 2

1 2 3 4 5 6

Comments to this Manuals

No comments

Cadet EBKNW Installation Guide Page 2

Comments to this Manuals

Related products and manuals for Space heaters Cadet EBKNW